Tyres & wheelsMazda Axela BM5FS
Mazda Axela BM5FS: Cold Tyre Pressure for 16- and 18-Inch Wheels
Find the correct Axela BM5FS factory tyre pressure: Mazda's 205/60R16 package uses 250/250 kPa and its SKYACTIV-G 1.5 215/45R18 package uses 240/220 kPa. Includes a cold-tyre inspection routine.
- Time
- 10–15 minutes
- Difficulty
- Easy
- Tools
- 3 needed
- Instructions
- 7 steps
Applies to Mazda Axela BM5FS · 2013–2017. Mazda Axela BM5FS fitted with the cited original 205/60R16 92V or 215/45R18 89W factory tyre packages; placard takes priority.. Always compare the described parts, labels and specifications with your own vehicle and manual.
Tools and materials
- Accurate cold-tyre pressure gauge
- Air pump or compressor
- Driver's-door factory pressure label
Step-by-step instructions
Follow these steps
Follow the written instructions in order; illustrations are optional, not a requirement for a complete guide. If a component or label looks different on your car, stop and check your own manual.
- Step 1 of 7
Read the exact sidewall size and engine version
Check actual tyre sidewall size and BM5FS specification. The Mazda table distinguishes 205/60R16 from 215/45R18, and 1.5-litre configurations from 2.2-litre diesel.
Check before moving onAll steps ↑Original wheel package and placard agree.
- Step 2 of 7
Choose the 16- or 18-inch target
For 205/60R16 92V use 250 kPa front/250 rear. For 215/45R18 89W fitted to a Mazda SKYACTIV-G 1.5 BM5FS use 240 kPa front/220 rear. Actual vehicle placard overrides this edition if different.
Check before moving onAll steps ↑Tyre size and front/rear targets recorded.
- Step 3 of 7
Measure only when tyres are cold
Take measurements before driving or after sufficient cooling. Park safely, remove one valve cap at a time and keep it clean.
Check before moving onAll steps ↑Wheels are cool and the valve is accessible.
- Step 4 of 7
Read front and rear pressures separately
Hold gauge squarely on the valve stem and note front left, front right, rear left and rear right values. Repeat any implausible measurements before adjusting.
Check before moving onAll steps ↑Four consistent readings are recorded.
- Step 5 of 7
Adjust towards the verified Mazda values
Inflate or release air in small increments, check again and use the specified figure for each axle. Mazda notes the driver's-side body label is the authoritative vehicle reference.
Check before moving onAll steps ↑Every tyre matches its original vehicle specification.
- Step 6 of 7
Inspect tread and refit caps
While checking each tyre, look for abnormal wear, bulges, cracks or embedded debris. Refit caps by hand and address any damage before continued use.
Check before moving onAll steps ↑All caps secure and no obvious tyre problem overlooked.
- Step 7 of 7
Record the results and monitor changes
Keep the date and four pressure readings for comparison. Recheck periodically, before long trips and when handling changes or one wheel loses pressure faster than the others.
Check before moving onAll steps ↑Pressure values retained for future comparison.
References & limitations
Where these instructions come from
Mazda Axela BM5FS fitted with the cited original 205/60R16 92V or 215/45R18 89W factory tyre packages; placard takes priority.
The 215/45R18 rear figure differs for 2.2L diesel variants (230 kPa); do not borrow those values for the BM5FS 1.5L. Non-factory wheel packages require further verification.
Mazda official owner manual ↗Manual section: Mazda Axela BN electronic owner's manual, tyre and wheel specifications, 'タイヤ空気圧' section 07020200: 205/60R16 250/250; 215/45R18 SKYACTIV-G1.5 or D1.5 240/220; D2.2 240/230.
Instructions checked against manufacturer documentation; not a physical inspection of every vehicle.