Cabin maintenanceToyota Vitz NSP130

Toyota Vitz NSP130: Cabin Air Filter Replacement (2014 Manual)

A source-backed Vitz NSP130 DIY cabin-filter change with glove-box damper, upper and lower catches, slide-out cover and the Toyota UP-arrow orientation.

Time
15–25 minutes
Difficulty
Easy
Tools
2 needed
Instructions
7 steps

Applies to Toyota Vitz NSP130 · 2018 reference. Toyota Vitz NSP130 2014-era generation whose passenger glove-box and HVAC filter carrier match the cited manual.. Always compare the described parts, labels and specifications with your own vehicle and manual.

Manual-referencedToyota official owner manualToyota Vitz 2014 manual printed pp. 258–260, §6-2 'Air-conditioning filter replacement'; interval and UP-arrow diagram.
Review evidence and limitations ↓

Tools and materials

  • Exact-fit Vitz NSP130 replacement cabin filter
  • 2014 Vitz owner manual

Step-by-step instructions

Follow these steps

Follow the written instructions in order; illustrations are optional, not a requirement for a complete guide. If a component or label looks different on your car, stop and check your own manual.

  1. Step 1 of 7

    Verify the original NSP130 housing

    Confirm chassis generation and locate the correct 2014 Vitz filter service section. Toyota recommends 20,000 km replacement normally, or 10,000 km in high-traffic/dusty/cold environments.

    Check before moving on

    Glove box and filter housing match the reference.

    All steps ↑
  2. Step 2 of 7

    Park and switch the ignition off

    Park safely and switch to LOCK if a conventional ignition is fitted or OFF if the Smart Entry switch is fitted. Remove loose glove-box contents.

    Check before moving on

    Ignition off and compartment clear.

    All steps ↑
  3. Step 3 of 7

    Release damper and glove-box stops

    Open the glove box, disconnect the damper-stay pin, squeeze side walls to release the upper retainers one by one, then free the lower catches as drawn in Toyota's instructions.

    Check before moving on

    Damper is detached and the box is free without stressed catches.

    All steps ↑
  4. Step 4 of 7

    Open the slide-out filter cover

    Release the filter-cover fastener, slide the cover in the indicated direction and remove it without levering off the tabs.

    Check before moving on

    The cover releases without damage.

    All steps ↑
  5. Step 5 of 7

    Seat the replacement with the UP marking upwards

    Remove old element, compare its size and frame to the replacement and install the new Toyota-style element with its UP arrow facing up. Consult aftermarket instructions if the substitute displays only AIR FLOW.

    Check before moving on

    New element sits level and UP arrow is correctly oriented.

    All steps ↑
  6. Step 6 of 7

    Reinstall the cover and glove box

    Guide the cover into its designated engagement point before latching, as Toyota illustrates, then raise the glove box, reseat catches and reconnect the damper.

    Check before moving on

    Damper and both catches are secure.

    All steps ↑
  7. Step 7 of 7

    Test the fan and look for noise

    Switch the HVAC fan on briefly and verify normal airflow. If reduced airflow persists, inspect for other HVAC faults rather than forcing the housing open again.

    Check before moving on

    No new rattle; fan moves air normally.

    All steps ↑

References & limitations

Where these instructions come from

Toyota Vitz NSP130 2014-era generation whose passenger glove-box and HVAC filter carrier match the cited manual.

This applies to Toyota's UP-marked filter and its 2014 layout; not all aftermarket airflow arrows mean UP. Interval 20,000 km normally, 10,000 km in heavy-traffic or dusty/cold use.

Toyota official owner manual ↗

Manual section: Toyota Vitz 2014 manual printed pp. 258–260, §6-2 'Air-conditioning filter replacement'; interval and UP-arrow diagram.

Instructions checked against manufacturer documentation; not a physical inspection of every vehicle.